JavaScript seems to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website. Click here for instructions on enabling javascript in your browser.

Result Pages:
5/16" Inlet Fitting / Power Valve Gaskets, 5 pack

Gasket OD" .410"
Gasket ID" .312"
Gasket Thickness" .031"
Quantity: 5 gaskets Fits:
Rochester M (Monojet) carburetors
Rochester H, HV carburetors
Rochester 2G (Twojet) carburetors (Power Valve)
Rochester 2SE (Varajet) carburetors
Rochester 4G (Fourjet) carburetors
Mercarb Marine 2bbl carburetors (Power Valve)
Holley carburetors
Nikki carburetors
Stromberg WW, WWC carburetors
Stromberg EE-1 carburetors…see more

Part Number
2233C
5/16" Inlet Fitting / Sight Plug Copper Gaskets, 5 pack

Quantity: 5 gaskets
Gasket OD" .500"
Gasket ID" .314"
Gasket Thickness" .033"
Gasket Material: Copper Fits:
Holley carburetors
Aisan carburetors Used for:
Sight plug gaskets
Inlet fitting gaskets…see more

Part Number
2233G
5/16" Quadrajet Carburetor Primary Throttle Shaft Bushings, 10 p


Bushing is designed to work in all Q-Jets on both the driver and passenger side of the...see more

10 oil impregnated bronze sleeve bushings are used to repair worn throttle shafts on the Rochester Quadrajet carburetors. Application: All Rochester Q-Jets
Fits 5/16" throttle shafts.
Note: Only for use on Primary side of Quadrajet carburetor.
1/2" length bushing is designed to work in all Q-Jets on both the driver and passenger side of the base plate. The 5/8" bushing (4312) may be used on the driver side if desired. Quantity: 10 bushings We HIGHLY recommend the use of Carburetor Bushing installation kit #4301 to accurately bore carburetor throttle shaft housings.…see more

Part Number
4311
5/16" Steel Fuel Line Clamps - (5-pak)

Specifications: Fits 5/16" carburetor fuel line.
Clamp OD: .590"
Clamp width: .315"
Color: Black Quantity: 5 clamps We recommend:
5/16" Ethanol rated fuel line, item #4298F5/16…see more

Part Number
2260A
5/16" Wire Type Fuel Line Clamps - (5-pak)

Specifications: Fits 5/16" carburetor fuel line.
Clamp OD: .590"
Clamp wire size: .062"
Color: Black Quantity: 5 clamps We recommend:
5/16" Ethanol rated fuel line, item #4298F5/16…see more

Part Number
2260B
5/32" Rubber Vacuum Caps

Rubber vacuum caps are used to plug unused vacuum fittings. Quantity: 5 Caps…see more

Part Number
4291
5/8" Inlet Fitting Gaskets - Rubber Coated, 5 pack

Inlet fitting gaskets for carburetors with 5/8" diameter inlets. Made from aluminum center with rubberized coating on each side.
Quantity: 5 gaskets
Gasket OD" .875"
Gasket ID" .620" (5/8")
Gasket Thickness: .030" Fits:
Carter AFB, AVS carburetors
Carter TQ (Themo-Quad) carburetors
May fit other carburetors too.…see more

Part Number
2233R
5/8" Inlet Fitting Gaskets, 5 pack


Gasket OD" .815" Gasket ID" .640" OEM# 7001597...see more

Inlet fitting gaskets for carburetors with 5/8" diameter inlets.
Quantity: 5 gaskets
Gasket OD" .815"
Gasket ID" .640"
OEM# 7001597…see more

Part Number
2233
5/8" Inlet Fitting Gaskets, 5 pack


Quantity: 5 gaskets
Gasket OD" .875" (7/8")
Gasket ID" .625" (5/8")
Gasket Thickness: .045" Note:
Replacement gasket for Q2215A - Banjo Inlet Fitting…see more

Part Number
2233J
5/8"-18 x #6 AN Fuel Inlet Adapter Fitting


No machine work or tapping is required, adapter uses standard Rochester 5/8"-18 threads....see more

Adapter fitting allows use of high performance racing fuel hoses and fittings. Adapter fitting has a female 5/8"-18 flared end that screws into the OEM inlet fitting. Number 6 AN male fitting is flared to accept standard #6 AN female hose fittings. Great for applications where custom steel braided fuel line is used. Fits factory and aftermarket mechanical fuel pumps with 5/8"-18 thread connections. No machine work or tapping is required, adapter uses standard Rochester 5/8"-18 threads.
Quantity: 1 fitting…see more

Part Number
2224
5/8"-18 x #8 Fuel Inlet AN Adapter Fitting


Number 8 AN male fitting is flared to accept standard #8 AN female hose fittings....see more

Adapter fitting allows use of high performance racing fuel hoses and fittings. Adapter fitting has a female 5/8"-18 flared end that screws into the OEM inlet fitting. Number 8 AN male fitting is flared to accept standard #8 AN female hose fittings. Great for applications where custom steel braided fuel line is used. Fits factory and aftermarket mechanical fuel pumps with 5/8"-18 thread connections. No machine work or tapping is required, adapter uses standard Rochester 5/8"-18 threads.
Quantity: 1 fitting…see more

Part Number
2225
5/8"-18 x 1/4 Pipe Thread - Fuel Inlet Reducer Fitting


Fits Rochester 4G & 2G carburetors...see more

Male Thread: 5/8" -18
Female Thread: 1/4" pipe
Overall length: .900"
ID: .220"
Wrench size: 3/4"
Quantity: 1 fitting Fits Rochester 4G & 2G carburetors…see more

Part Number
2218F
5/8"-18 x 3/8" Barbed Nipple


Threaded male side of fitting is flared to seal against the factory inlet fitting....see more

This fitting makes it easy to hook up a rubber gas line to your carburetor. Threaded male side of fitting is flared to seal against the factory inlet fitting. Barbed side of fitting is made to slip into a 3/8" rubber fuel line. Thread: 5/8-18 male Fits Rochester Quadrajet, 2G, 4G with 5/8"-18 threads
Fits Carter / Edelbrock AFB, AVS with 5/8"-18 threads…see more

Part Number
2242
5/8"-18 x 5/16" Barbed Nipple

This fitting makes it easy to hook up a rubber gas line to your carburetor. Threaded male side of fitting is flared to seal against the factory inlet fitting. Barbed side of fitting is made to slip into a 5/16" rubber fuel line. Thread: 5/8-18 male
Quantity: 1 fitting Fits Rochester Quadrajet, 4G, 2G
Fits Carter / Edelbrock AFB, AVS…see more

Part Number
2240
5/8"-20 with 3/8" barb - Fuel Inlet Reducer Fitting


Seal/gasket is included with fitting...see more

This fitting makes it easy to hook up a rubber gas line to your carburetor. Barbed side of fitting is made to slip into a 3/8" rubber fuel line.
Gasket is included with fitting.
Fits carburetors with 5/8"-20 inlet threads. OAL: 1.200"
Thread length: .290"
Thread: 5/8-20 male
Barb size: 3/8" Quantity: 1 fitting & 1 gasket Note:
Replacement gaskets are available, order item #2233J.…see more

Part Number
2244
5/8"-20 x #6 AN  - Adapter Inlet Fitting

Aluminum adapter inlet fitting allows use of high performance racing fuel hoses and fittings. Adapter fitting replaces OEM Inlet Fitting and screws into Carter / Edelbrock AFB AVS carburetors using the original style sealing gasket. Number 6 AN male fitting is flared to accept standard #6 AN female hose fittings. Great for high horsepower application where custom steel braided fuel line is used. No machine work or tapping is required, adapter uses standard 5/8"-20 threads. Seal is included with fitting. Fits Carter AFB, AVS
Fits Edelbrock AFB, AVS…see more

Part Number
2222A
5/8"-20 x 1/2"-20 Fuel Inlet Fitting, .350" Extended Threads

OAL: .800"
Thread length: .350"
Thread: 5/8-20 male
Thread: 1/2-20 female w/ inverted flare
Quantity: 1 fitting and 1 seal. Fits:
Rochester 4G carburetors
Rochester 2G carburetors
Carter AFB carburetors
Carter TQ carburetors Seal is included with fitting. Fits carburetors with 5/8" inlets.…see more

Part Number
2218D
5/8"-20 x 1/2"-20 Fuel Inlet Fitting, OEM # 7000262


Includes gasket, Fits: Rochester 2G, 4G and Carter AFB carburetors...see more

Replacement 2G Inlet fitting. Seal is included with fitting. Fits carburetors with 5/8" inlets. OAL: .685"
Thread length: .200"
Thread: 5/8-20 male
Thread: 1/2-20 female w/ inverted flare Fits:
Rochester 2G carburetors, 1954-up Olds
Rochester 4G carburetors
Carter AFB carburetors
OEM # 7000262…see more

Part Number
2218C
5/8"-20 x 1/8" Pipe Thread, Fuel Inlet Fitting

Fits carburetors with 5/8" inlets. Dimensions:
OAL: 1/2"
Thread length: .320"
Thread: 5/8-20 male
Thread: 1/8" pipe thread female
Nut (Wrench) size: 3/4" Fits:
Carter AFB, AVS carburetors
Carter TQ, Themo-Quad carburetors
Rochester 4G, Four-Jet carburetors
Rochester B, BC, BV carburetors
Rochester Monojet carburetors Note:
Requires use of gasket # 2233J (Sold separately)  …see more

Part Number
2219A
5/8"-20 x 3/8" Hose Barb - Banjo Inlet Fitting


Allows easy positioning of fuel line. No machine work required, banjo kit contains...see more

Inlet ‘Banjo’ Fitting for 5/8"-20 threaded castings. Converts inlet position from front to side or side to front. 3/8" barb accepts 3/8" diameter rubber fuel line. Allows easy positioning of fuel line. No machine work required, banjo kit contains everything you need including gaskets. Banjo fitting design allows use of OEM fuel filters. Note:
Replacement banjo gaskets: #2233J (sold separately, uses 2 gaskets)…see more

Part Number
2215A
Result Pages: