QuadrajetParts.com - Carburetor Parts Superstore
Carburetor Parts & Rebuild Kits for Carter, Holley, Ford, Rochester & Stromberg.
7/16"-24 x 1/2"-20 - Inlet Adaptor Fitting
Hard to find fitting, VERY limited quantities!
Adapts/reduces 5/16" steel fuel line to 1/4" line.
Male Threads: 7/16"-24 (Flare fitting)
Female Threads: 1/2"-20 (Flare fitting, 5/16" steel fuel line)
Over all length: .865"
Orifice diameter: .175"
Quantity: 1…see more
- Part Number
- 2218U
7/32" Rubber Vacuum Caps
Rubber vacuum caps are used to plug unused vacuum fittings. Quantity: 5 caps…see more
- Part Number
- 4292
7/8" Inlet Fitting Gaskets - Extra Thick Nylon, 5 pack
Extra thickness and nylon material helps correct leaking inlet fittings.
Inlet fitting gaskets for carburetors with 7/8" diameter inlets.
Quantity: 5 gaskets
Gasket OD" 1.040"
Gasket ID" .875" (7/8")
Gasket Thickness: .062"
Gasket Material: Nylon
Fits: Rochester, Carter, Ford/Motorcraft, Holley carburetors.
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2231B
7/8" Inlet Fitting Gaskets - Rubber Coated Aluminum, 5 pack
Inlet fitting gaskets for carburetors with 7/8" diameter inlets.
Quantity: 5 gaskets
Gasket OD" 1.06"
Gasket ID" .875" (7/8")
Gasket Thickness: .030"
Rochester OEM Gasket # 7032508
Fits:
Carter AFB, AVS carburetors.
Carter WCFB carburetors.
Carter YF, YFA carburetors.
Ford/Motorcraft 4300, 4350 carburetors.
Ford/Motorcraft 2700 VV, 7200 VV carburetors.
Holley 3160, 4150, 4152, 4160 carburetors.
Holley 4165, 4175 carburetors.
Holley 4180, 4190 carburetors.
Holley 4360 carburetors.
Holley 2300, 2380 carburetors.
Holley 5200, 5210, 5220 carburetors.
Holley 6500, 6510, 6520 carburetors.
Rochester Quadrajet carburetors.
Rochester 4G (Fourjet) carburetors.
Rochester B, BC, BV carburetors.
Rochester H carburetors.
Rochester Monojet carburetors.
Rochester 2G (Twojet) carburetors.
Rochester Dualjet 210 carburetors.
Rochester Varajet carburetors.
May fit other applications with 7/8" fuel fitting.
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2231C
7/8" Inlet Fitting Gaskets, 5 pack
Fits Rochester and Carter carburetors - 7/8" diameter inlet QJet carburetors can be identified by...see more
Inlet fitting gaskets for carburetors with 7/8" diameter inlets.
Quantity: 5 gaskets
Gasket OD" 1.055"
Gasket ID" .875" (7/8")
Gasket Thickness: .050"
Rochester OEM Gasket # 7010010
Fits: Rochester, Carter, Ford/Motorcraft, Holley carburetors.
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2231
7/8" x 1/2"-20 - O-Ring Inlet Repair Fitting
Very Limited Quantities!
Fits:
Holley carburetors with 7/8" inlet threads.
Rochester Monojet carburetors
Do not use with Rochester 2 bore or Rochester Quadrajet.
Thread: 1/2-20 female w/ inverted flare
O-ringed repair fitting repairs carburetors with stripped fuel inlet threads. Expanding dual "O" ring fitting effectively repairs leaks at the fuel inlet caused by stripped or damaged threads in the carburetor casting.
For use with carburetors with 7/8" diameter inlet fitting and 5/16" gas line.
Note: You will need to install an in-line fuel filter, as this inlet fitting will not allow the use of the stock style fuel filter.…see more
- Part Number
- 2205A
7/8" x 5/8"-18 - O-Ring Inlet Repair Fitting
Very Limited Quantities!
Fits:
Holley carburetors with 7/8" inlet threads.
Rochester Monojet carburetors
Do not use with Rochester 2 bore or Rochester Quadrajet.
Thread: 5/8-18 female w/ inverted flare
O-ringed repair fitting repairs carburetors with stripped fuel inlet threads. Expanding dual "O" ring fitting effectively repairs leaks at the fuel inlet caused by stripped or damaged threads in the carburetor casting.
For use with carburetors with 7/8" diameter inlet fitting and 3/8" gas line.
Note: You will need to install an in-line fuel filter, as this inlet fitting will not allow the use of the stock style fuel filter.…see more
- Part Number
- 2204A
7/8"-20 Inlet Plug & Gasket
Over-all length: .785"
Thread: 7/8-20 male
Quanity: 1 fitting & 1 gasket
Material: Steel
Gasket is included with fitting.
Applications:
Holley carburetors…see more
- Part Number
- 2218S
7/8"-20 x #6 AN - Adapter Inlet Fitting
Adapter fitting replaces OEM Inlet Fitting and screws into Rochester Quadrajet & 2G casting using...see more
Aluminum adapter inlet fitting allows use of high performance racing fuel hoses and fittings. Adapter fitting replaces OEM Inlet Fitting and screws into Rochester Quadrajet & 2G casting using the original style sealing gasket. Number 6 AN male fitting is flared to accept standard #6 AN female hose fittings. Great for high horsepower application where custom steel braided fuel line is used.
No machine work or tapping is required, adapter uses standard Rochester 7/8"-20 threads. Seal is included with fitting.
Fits Rochester Quadrajet, 2G, Holley
Quantity: 1 fitting
Replacement gaskets available:
#2231
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2222
7/8"-20 x 1/2"-20 - .400" Thread Inlet Fitting
OEM # 7013525...see more
OAL: .800"
Thread length: .400"
Thread: 7/8-20 male
Thread: 1/2-20 female with inverted flare
OEM # 7013525
Quantity: 1 fitting & 1 gasket Replacement Inlet fitting has .400" threads to grab deep into the carburetor casting. Accepts 5/16" steel fuel line. Gasket is included with fitting.
Note: Ensure that carburetor casting has sufficient threads to accept deeper fitting.
Applications:
Rochester 2G (Two Jet) carburetors
Carter YF, YFA carburetors
Holley carburetors
Replacement gaskets available:
2231…see more
- Part Number
- 2218A
7/8"-20 x 1/2"-20 - Inlet Fitting
Replacement Inlet fitting. Seal is included with fitting.
OAL: .650"...see more
Fits:
Rochester Quadrajet carburetors
Fits Rochester 4G carburetors
Fits Rochester 2G carburetors
Carter / Edelbrock AFB, AVS carburetors
Carter WCFB carburetors
Holley carburetors
OAL: .650"
Thread length: .300"
Male Thread: 7/8-20 male
Female Thread: 1/2-20 female w/ inverted flare (accepts 5/16" steel gas line)
Quantity: 1 (Seal is included with fitting)
Replacement gaskets available:
#2231
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2218E
7/8"-20 x 1/8"-Pipe Thread - .500" Extended Thread Inlet Fittin
Replacement Inlet fitting has extended threads to grab deeper into carburetor castings. Many main body castings have threads that are not used by OEM inlet fitting.
Seal is included with fitting. Fits carburetors with 7/8" inlets, uses short fuel filter.
OAL: .900"
Thread length: .500"
Thread: 7/8-20 male
Thread: 1/8 pipe thread
Quantity: 1 fitting
Replacement gaskets available:
#2231
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2218B
7/8"-20 x 5/8"-18 - .500" Extended Thread Inlet Fitting
Replacement Inlet fitting has extended threads to grab deeper into carburetor castings....see more
Replacement Inlet fitting has extended threads to grab deeper into carburetor castings. No machine work or tapping is required, many main body castings have threads that are not used by OEM inlet fitting.
This is not a self tapping fitting. Seal is included with fitting. Fits carburetors with 7/8" inlets and 3/8" gas line, uses short fuel filter.
OAL: 1.07"
Thread length: .500"
Thread: 7/8-20 male
Thread: 5/8-18 female w/ inverted flare
Fits Rochester Quadrajet, 2G, Varajet
Fits Carter / Edelbrock AFB, AVS
Quantity: 1 Fitting & 1 Gasket
Replacement gaskets available:
#2231
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2206
7/8"-20 x 5/8"-18 - .650" Extended Thread Inlet Fitting
Replacement Inlet fitting has extended threads to grab deeper into carburetor castings. No machine work or tapping is required...see more
Replacement Inlet fitting has extended threads to grab deeper into carburetor castings. No machine work or tapping is required, many main body castings have threads that are not used by OEM inlet fitting. Verify that your main body casting has sufficient threads to accept this extended thread fitting.
This is not a self tapping fitting. Seal is included with fitting. Fits carburetors with 7/8" inlets and 3/8" gas line, uses short fuel filter.
OAL: 1.100"
Thread length: .650"
Thread: 7/8-20 male
Thread: 5/8-18 female w/ inverted flare
Fits Rochester Quadrajet, 2G
Fits Carter / Edelbrock AFB, AVS
Quantity: 1 Fitting & 1 Gasket
Replacement gaskets available:
#2231
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2217
7/8"-20 x 5/8"-18 - HOLLEY Inlet Fitting
Originally designed for Holley side fuel bowl carburetors as it allows additional fuel bowl screw boss clearence, but it can be used on other carburetor types that accept 7/8"-20 threads.
Fits:
Rochester Quadrajet carburetors
Fits Rochester 4G carburetors
Fits Rochester 2G carburetors
Carter / Edelbrock AFB, AVS carburetors
Carter WCFB carburetors
Holley carburetors
Specifications:
OAL: .775"
Thread length: .330"
Male Thread: 7/8-20 male
Hex-head size: 1" (Wrench size)
Female Thread: 5/8-18 female w/ inverted flare (accepts 3/8" steel gas line)
Quantity: 1 (Seal is included with fitting)
Replacement gasket/seal available:
#2231
…see more
- Part Number
- 2207
7/8"-20 x 5/8"-18 - Inlet Fitting (long)
Replacement Inlet fitting fits Rochester Quadrajet and 2G carburetors.
Seal is included with fitting....see more
Replacement Inlet fitting fits Rochester Quadrajet and 2G carburetors.
Seal is included with fitting. Fits Rochester carburetors with 7/8" inlets and 3/8" gas line, uses long fuel filter.
Thread: 7/8-20 male
Thread: 5/8-18 female w/ inverted flare
Fits Rochester Quadrajet, 2G
Quantity: 1 Fitting & 1 Gasket
Replacement gaskets available:
#2231
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2213
7/8"-20 x 5/8"-18 - Self Tapping Inlet Fitting (Long)
Very Limited Quantities!
Self tapping inlet fitting for use with 7/8" diameter inlet with 3/8" gas line. Includes new inlet gasket. Uses long fuel filter.
Self tapping repair fitting repairs Rochester carburetors with stripped threads. Made of tough steel, this self tapping fitting will reach deeper into the main-body casting, cut and engage new threads. Quick and easy to install.
Thread: 7/8-20 male
Thread: 5/8-18 female w/ inverted flare
Fits Rochester Quadrajet, 2G
Quantity: 1
Installation Instructions:
This fitting has an oversize thread with the cutting action of a tap. Use care to start it straight.
For good cutting action, rotate the new fitting 1/2 turn forward, then back it up 1/4 turn, then forward 1/2 turn, continue until the new fitting bottoms with the hex section of the fitting against the casting.
Remove the fitting and clean all metal cuttings from both the carburetor cavity and the fitting.
Install the filter element spring, filter, gasket and fitting.
Re-install carb and test carefully for leaks, with engine running and full fuel pump pressure at the carburetor.
If any leakage occurs in final test, DO NOT USE, until proper corrective action has been taken.
Note: #2231B (Extra thick nylon gaskets - sold separately) offers additional sealing capability and may help seal fitting if leakage is encountered.
Note: Fitting color may be Black, Silver or Gold.
Quadrajet carburetor note:
7/8" inlet fittings are found on all 1965 thru 1971 automobile and truck Quadrajet carburetors, plus all year marine Quadrajet carburetors.
7/8" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located up against the tightening nut of the inlet fitting. After installation of the 7/8" inlet fitting on the carburetor, the inlet gasket is visible.…see more
- Part Number
- 2202
7/8"-20 x 7/16"-24 - .500" Extended Thread Inlet Fitting
Replacement inlet fitting has extended threads to grab deeper into carburetor castings. Many main body castings have threads that are not used by OEM inlet fitting.
Seal is included with fitting. Fits carburetors with 7/8" inlets, uses short fuel filter.
OAL: .900"
Thread length: .500"
Thread: 7/8-20 male
Thread: 7/16-24 female
Quantity: 1 fitting & 1 Gasket…see more
- Part Number
- 2218I
9/16" Gaskets - Inlet Banjo / Needle & Seat
Quantity: 5 gaskets
Gasket OD" .710"
Gasket ID" .567"
Gasket Thickness" .031"
Material: Aluminum & Rubber
Fits:
Carter BBD carburetors
Holley carburetors…see more
- Part Number
- 2233H
9/16" Inlet Fitting Gaskets, 5 pack
Inlet fitting gaskets for carburetors with 9/16" diameter inlets.
Quantity: 5 gaskets
Gasket OD" .750"
Gasket ID" .565"
Gasket Thickness" .046"
Fits:
Ford/Motorcraft carburetors
Holley carburetors…see more
- Part Number
- 2233A
9/16" Inlet Fitting Gaskets, 5 pack
Inlet fitting gaskets for carburetors with 9/16" diameter inlets.
Quantity: 5 gaskets
Gasket OD" .690"
Gasket ID" .570"
Gasket Thickness" .032"
Fits:
Holley 885 carburetors
Holley 1901 carburetors…see more
- Part Number
- 2233E
9/16"-24 x 1/2"-20 - Inlet Fitting
Male Threads: 9/16"-24
Female Threads: 1/2"-20 (5/16" steel fuel line)
Over all length: .865"
Orifice diameter: .212"
Quantity: 1
Fits:
Ford/Motorcraft 2100 carburetors
Ford/Motorcraft 2150 carburetors
Ford/Motorcraft 4100 carburetors…see more
- Part Number
- 2218O
9/16"-24 x 3/8" Barbed Nipple
This fitting makes it easy to hook up a rubber gas line to your carburetor. Barbed side of fitting is made to slip into a 3/8" rubber fuel line. Fits Holley carburetors. Thread: 9/16"-24 male Hex size: 11/16" (wrench size) Quantity: 1 fitting…see more
- Part Number
- 2245C
9/16"-24 x 5/16" Barbed Nipple
This fitting makes it easy to hook up a rubber gas line to your carburetor. Barbed side of fitting is made to slip into a 5/16" rubber fuel line. Fits Holley carburetors. Thread: 9/16"-24 male Hex size: 11/16" (wrench size) Quantity: 1 fitting…see more
- Part Number
- 2245D
9/16"-24 x 5/16" Barbed Nipple - Banjo Fitting Assembly
Width of banjo: .415"
Thread size: 9/16-24
Barb hose size: 5/16"
Quanity: 1 fitting w/gaskets
Accepts 5/16" rubber fuel line.
Applications:
Holley 4150, 4160 style carburetors
Note:
Replacement banjo gaskets: Q2233H (sold separately)…see more
- Part Number
- 2215B
9/16"-24 x 5/8"-18 - Fuel Inlet Fitting
OAL: .775"
Thread length: .350"
Thread: 9/16-24 male
Thread: 5/8-18 female with inverted flare
Quanity: 1 fitting
Accepts 3/8" steel fuel line.
Applications:
Holley 4150, 4160 style carburetors
Holley 4165, 4175 style carburetors
Holley 4180, 4190 style carburetors
Holley 2300 style carburetors
Note:
Use with inlet gasket 2233A (sold separately)…see more
- Part Number
- 2218R
Accelerator Pump - 3/4" x 1.96" Leather
Fits:
Carter BBD carburetors
Stromberg WW, WWC carburetors
Dimensions:
Over all length: 1.96"
Pump Cup diameter: 3/4"
Carter Accelerator Pump Plunger - Leather cup is designed to withstand today's fuel with alcohol / ethanol.
Quantity: 1…see more
- Part Number
- 1061L
Accelerator Pump Assembly, 13/16" Ethanol Resistant (Length: 2.5
Carter / Edelbrock accelerator pump assembly is designed to withstand todays fuel with alcohol / ethanol...see more
Fits:
Carter AFB & AVS carburetors
Edelbrock Performer AFB and Thunder AVS carburetors
Carter WCFB carburetors
13/16" Carter / Edelbrock accelerator pump assembly is designed to withstand todays fuel with alcohol / ethanol. Comes with highest quality pump cup that stands up to todays new fuels.
Note: Not all blue accelerator pump cups on the market are resistant to todays new fuels, dont be mislead by the color, demand the best!
Dimensions:
Over all length (OAL): 2.550"
Pump Cup diameter: 13/16"
Stem Length 1.00" (length above from spring retainer to stem tip)
Cup Style: Double lip (ethanol resistant)
Carter AFB/AVS carburetors serviced with this accelerator pump:
9400S, 9500S, 9501S, 9502S, 9503S, 9504S, 9510S, 9511S, 9605S, 9606S, 9607S, 9625S, 9626S, 9627S, 9635S, 9636S, 9637S, 9638S, 9641S, 9755S, 9756S, 9757S, 9758S
Edelbrock Perfomer AFB 500, 600, 750, 800 carburetors serviced with this rebuild kit:
1403, 1404, 1400, 1405, 14054, 1406, 14064, 1407, 1411, 1412, 1413, 1409, 1410
Replacement accelerator pump cup: Item #1014…see more
- Part Number
- 1008A
Accelerator Pump Cup - 3/4" Ethanol Resistant
Fits:
Carter BBD carburetors
Carter RBS carburetors
Ethanol resistant pump cup
Cup outside diameter: 3/4"
Cup inside diameter: .406"
Quantity: 1
Instructions when replacing accelerator pumps:
It is very important that the accelerator pump bore is completely smooth. Today's fuels with ethanol have less lubrication and demand super smooth pump bore surfaces. Polish pump bore with crocus cloth as required. Rough pump bore surfaces will cause pump cup to stick to bore and tear or dislodge from plunger assembly.
Do not allow carburetor cleaner come in contact with pump assembly.
Coat outer edges of pump cup with a light coating of grease, if pump bore is not submerged in fuel.
Long term vehicle storage:
If vehicle is dormant and fuel bowl is allowed to go dry, pump cup has a much higher chance of sticking to pump bore. If bowl has run dry, fill fuel bowl with fuel before pumping accelerator pump assembly.…see more
- Part Number
- 1012B
Accelerator Pump Cup Garter Spring - Holley AA-1, 852, 2100, 211
Dimensions:
Outside diameter: .600"
Inside diameter: .375"
Quantity: 1…see more
- Part Number
- 1042B
Accelerator Pump Cup- 3/4", Ethanol Resistant
Specs:
Cup OD: 3/4"
Cup hole ID: .115"
Cup height: .240"
Fluroelastomer (Ethanol Resistant)
OEM # C7AZ-9572-A
Fits:
Ford 4300 carburetors
Instructions when replacing accelerator pumps:
It is very important that the accelerator pump bore is completely smooth. Today's fuels with ethanol have less lubrication and demand super smooth pump bore surfaces. Polish pump bore with crocus cloth as required. Rough pump bore surfaces will cause pump cup to stick to bore and tear or dislodge from plunger assembly.
Do not allow carburetor cleaner come in contact with pump assembly.
Coat outer edges of pump cup with a light coating of grease, if pump bore is not submerged in fuel.
Long term vehicle storage:
If vehicle is dormant and fuel bowl is allowed to go dry, pump cup has a much higher chance of sticking to pump bore. If bowl has run dry, fill fuel bowl with fuel before pumping accelerator pump assembly.…see more
- Part Number
- 1065H
Accelerator Pump Cup, 11/16", Ethanol Resistant/Fluoroelastomer
This heavy duty 11/16" accelerator pump cup is resistant to the ethanol / alcohol found in today's gasoline. Easy to change. Great for both stock and performance carburetors. Correct your accelerator pump cup problems with this new pump cup.
Fits:
Holley 1945 carburetors
Holley 6145 carburetors
Holley 1949 carburetors
Holley 6149 carburetors
Various Holley carburetors
Instructions when replacing accelerator pumps:
It is very important that the accelerator pump bore is completely smooth. Today's fuels with ethanol have less lubrication and demand super smooth pump bore surfaces. Polish pump bore with crocus cloth as required. Rough pump bore surfaces will cause pump cup to stick to bore and tear or dislodge from plunger assembly.
Do not allow carburetor cleaner come in contact with pump assembly.
Coat outer edges of pump cup with a light coating of grease, if pump bore is not submerged in fuel.
Long term vehicle storage:
If vehicle is dormant and fuel bowl is allowed to go dry, pump cup has a much higher chance of sticking to pump bore. If bowl has run dry, fill fuel bowl with fuel before pumping accelerator pump assembly.…see more
- Part Number
- 1071A
Accelerator Pump Cup, 23/32", Ethanol Resistant/Fluoroelastomer
This heavy duty accelerator pump cup is resistant to the ethanol / alcohol found in today's gasoline. Easy to change. Great for both stock and performance carburetors. Correct your accelerator pump cup problems with this new pump cup.
Specs:
Actual measured OD: .700"
Center hole ID: .145"
Fits:
Various Holley carburetors
Instructions when replacing accelerator pumps:
It is very important that the accelerator pump bore is completely smooth. Today's fuels with ethanol have less lubrication and demand super smooth pump bore surfaces. Polish pump bore with crocus cloth as required. Rough pump bore surfaces will cause pump cup to stick to bore and tear or dislodge from plunger assembly.
Do not allow carburetor cleaner come in contact with pump assembly.
Coat outer edges of pump cup with a light coating of grease, if pump bore is not submerged in fuel.
Long term vehicle storage:
If vehicle is dormant and fuel bowl is allowed to go dry, pump cup has a much higher chance of sticking to pump bore. If bowl has run dry, fill fuel bowl with fuel before pumping accelerator pump assembly.…see more
- Part Number
- 1071B
Accelerator Pump Cup, 23/32", Ethanol Resistant/Fluoroelastomer
This heavy duty accelerator pump cup is resistant to the ethanol / alcohol found in today's gasoline. Easy to change. Great for both stock and performance carburetors. Correct your accelerator pump cup problems with this new pump cup.
Specs:
Actual measured OD: .700"
Center hole ID: .320"
Fits:
Various Holley carburetors
Holley 1904, 1908, 1920, 1931, 1960
Holley 2209, 2210, 2245
Holley 2280, 6280C
Instructions when replacing accelerator pumps:
It is very important that the accelerator pump bore is completely smooth. Today's fuels with ethanol have less lubrication and demand super smooth pump bore surfaces. Polish pump bore with crocus cloth as required. Rough pump bore surfaces will cause pump cup to stick to bore and tear or dislodge from plunger assembly.
Do not allow carburetor cleaner come in contact with pump assembly.
Coat outer edges of pump cup with a light coating of grease, if pump bore is not submerged in fuel.
Long term vehicle storage:
If vehicle is dormant and fuel bowl is allowed to go dry, pump cup has a much higher chance of sticking to pump bore. If bowl has run dry, fill fuel bowl with fuel before pumping accelerator pump assembly.
…see more
- Part Number
- 1071H
Accelerator Pump Cup, 3/4", Double Lip Ethanol Resistant
Used in large bore 2 barrel Rochester 2G, 2GC, 2GE and 2GV carburetors....see more
3/4" accelerator pump cup is used in large bore 2 barrel Rochester 2G, 2GC, 2GE, 2GV and Rochester 4G carburetors.
Note: For use with accelerator pump plungers designed to accept the double lip pump cup.
Instructions when replacing Rochester accelerator pumps:
It is very important that the accelerator pump bore is completely smooth. Today's fuels with ethanol have less lubrication and demand super smooth pump bore surfaces. Polish pump bore with crocus cloth as required. Rough pump bore surfaces will cause pump cup to stick to bore and tear or dislodge from plunger assembly.
Do not allow carburetor cleaner come in contact with pump assembly.
Coat outer edges of pump cup with a light coating of grease, if pump bore is not submerged in fuel.
Long term vehicle storage:
If vehicle is dormant and fuel bowl is allowed to go dry, pump cup has a much higher chance of sticking to pump bore. If bowl has run dry, fill fuel bowl with fuel before pumping accelerator pump assembly.…see more
- Part Number
- 1012A
Accelerator Pump Cup, Holley 2100, 2110, Ethanol Resistant
Dimensions:
Outside diameter: .660" (21/32")
Inside diameter: .215"
Width: .200"
21/32" accelerator pump cup (ethanol resistant) is used in Holley carburetors.
Instructions when replacing Holley accelerator pumps:
It is very important that the accelerator pump bore is completely smooth. Today's fuels with ethanol have less lubrication and demand super smooth pump bore surfaces. Polish pump bore with crocus cloth as required. Rough pump bore surfaces will cause pump cup to stick to bore and tear or dislodge from plunger assembly.
Do not allow carburetor cleaner come in contact with pump assembly.
Coat outer edges of pump cup with a light coating of grease, if pump bore is not submerged in fuel.
Long term vehicle storage:
If vehicle is dormant and fuel bowl is allowed to go dry, pump cup has a much higher chance of sticking to pump bore. If bowl has run dry, fill fuel bowl with fuel before pumping accelerator pump assembly.…see more
- Part Number
- 1014A
Accelerator Pump Discharge Springs - (5 Pack)
OEM # 7002118...see more
Accelerator pump discharge springs.
Fits:
Rochester Two-Jet 2G carburetors
Rochester VaraJet 2SE, E2SE carburetors
Rochester Monojet M, MV, 1ME, 1MV carburetors
OEM # 7002118
Quantity: 5 Pack
Length: .930"
ID: .135"
Wire diameter: .010"
MADE IN USA…see more
- Part Number
- 1025A
Accelerator Pump Duration/Delayer Spring
Quantity: 1 spring...see more
Replacement accelerator pump duration/delayer spring.
Over all length: 1.95"
Diameter: .550"
Quantity: 1 spring
Fits:
Carter Thermo-Quad
Rochester Monojet M, MV, 1ME, 1MV
Holley 1940 carburetors…see more
- Part Number
- 1041B
Accelerator Pump Duration/Delayer Spring Carter AFB, AVS, Roches
Quantity: 1 spring, Spring OD: .430" tapers down to .410"...see more
Replacement Accelerator Pump Duration/Delayer Spring.
Fits:
Carter AFB carburetors
Carter AVS carburetors
Carter WCD, WGD, WGD-1 carburetors (Delayer spring)
Carter WCFB carburetors (Delayer spring)
Rochester H, HV 1bbl carburetors
Quantity: 1 spring
Spring OD: .430" tapers down to .410"
OAL (Over All length): 1.87"
Wire Diameter: .033"
Note:
When used on Carter carburetors (Pump # 1061G and #1061K), you will need to cut the spring in half to shorten.
…see more
- Part Number
- 1041A
Accelerator Pump Housing Cover Assembly - Holley 30 CC
Fits:
Holley 2300 carburetors
Holley 2380 carburetors
Holley 3160 carburetors
Holley 4010 carburetors
Holley 4011 carburetors
Holley 4150 carburetors
Holley 4152 carburetors
Holley 4160 carburetors
Holley 4165 carburetors
Holley 4175 carburetors
Holley 4180 carburetors
Holley 4190 carburetors
Barry Grant, Demon carburetors
Quantity: 1…see more
- Part Number
- 1073A
- Servicing Bi-Metal Choke Springs
- Ethanol (E-10) fuel in carbureted engines
- Where do I locate my carburetor number?
- How to Test a Vacuum Break / Pulloff
- #4802 Idle Pickup Tubes
- #3622 Power Piston Retaining Bushing
- O-Ring Inlet Repair Fuel Fitting
- #2702 Secondary Air Valve Spring Tension
- #4231B - Air Cleaner Repair Bracket
- Needle & Seats
- #2701 Secondary Air Valve Cam Replacement
- #2460-82 Changing Primary Metering Jets
- #2251/2252/2253 Fuel Filter Replacement
- #1742/1743 Secondary Well Plug Fix
- Float level adjustment for Quadrajet and Dualjet Carburetor
- Servicing the tamper resistant choke cover on Rochester carbs
- #1310-SR Mixture Control Solenoid Adjust
- What is a Carter Quadrajet?
- Quadrajet Model Designations
- Edelbrock Quadrajets
- #1003 Accelerator Pump Styles
- Exploded View 4MV 1975 thru
- Exploded View 4MV 1971 thru 1974
- Exploded View 4MV 1967 thru 1970
- Exploded View 4MV 1966
- Fuel Pressure
- Power Piston & Primary Metering Rods
- Fuel Inlets
- Exploded View 2G / 2GV
All Topics
- Carburetor Tech Info
- Mercury Marine Mercarb Carbureto
- Rochester 2G/Two Jet Tech
- Rochester Quadrajet Tech
Articles RSS Feed
Submit An Article