QuadrajetParts.com - Carburetor Parts Superstore
Carburetor Parts & Rebuild Kits for Carter, Holley, Ford, Rochester & Stromberg.
"P" 64P Quadrajet Primary Metering Rods, .064"/.026"
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods.
Rod dimension is NOT stamped on rod.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single full length taper design “P”
Cruise diameter: .064"
Power tip diameter:.026"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 64P rod has a large diameter of .064" and a small diameter "power tip" of .026". The .064" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.026") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "P" primary metering rods have the same small diameter power tip (.026"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2564P
"P" 67P Quadrajet Primary Metering Rods, .067"/.026"
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods.
Rod dimension is NOT stamped on rod.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single full length taper design “P”
Cruise diameter: .067"
Power tip diameter:.026"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 67P rod has a large diameter of .067" and a small diameter "power tip" of .026". The .067" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.026") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "P" primary metering rods have the same small diameter power tip (.026"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2567P
"P" 68P Quadrajet Primary Metering Rods, .068"/.026"
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods.
Rod dimension is NOT stamped on rod.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single full length taper design “P”
Cruise diameter: .068"
Power tip diameter:.026"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 68P rod has a large diameter of .068" and a small diameter "power tip" of .026". The .068" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.026") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "P" primary metering rods have the same small diameter power tip (.026"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2568P
"P" 69P Quadrajet Primary Metering Rods, .069"/.026"
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods.
Rod dimension is NOT stamped on rod.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single full length taper design “P”
Cruise diameter: .069"
Power tip diameter:.026"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 69P rod has a large diameter of .069" and a small diameter "power tip" of .026". The .069" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.026") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "P" primary metering rods have the same small diameter power tip (.026"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2569P
"P" 70P Quadrajet Primary Metering Rods, .070"/.026"
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods.
Rod dimension is NOT stamped on rod.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single full length taper design “P”
Cruise diameter: .070"
Power tip diameter:.026"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 70P rod has a large diameter of .070" and a small diameter "power tip" of .026". The .070" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.026") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "P" primary metering rods have the same small diameter power tip (.026"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2570P
"P" 70P Quadrajet Primary Metering Rods, .070"/.026"
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods.
Rod dimension is NOT stamped on rod.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single full length taper design “P”
Cruise diameter: .071"
Power tip diameter:.026"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 71P rod has a large diameter of .071" and a small diameter "power tip" of .026". The .071" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.026") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "P" primary metering rods have the same small diameter power tip (.026"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2570P
"P" 72P Quadrajet Primary Metering Rods, .072"/.026"
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods.
Rod dimension is NOT stamped on rod.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single full length taper design “P”
Cruise diameter: .072"
Power tip diameter:.026"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 72P rod has a large diameter of .072" and a small diameter "power tip" of .026". The .072" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.026") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "P" primary metering rods have the same small diameter power tip (.026"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2572P
"S" 62S NOS Quadrajet Primary Metering Rods, .062"/.036"
New Old Stock (NOS) original Rochester Products primary metering rods. These original rods are no longer produced by Rochester Products and very difficult to find.
Rochester Quadrajet primary metering rods are used to tailor primary part throttle air/fuel enrichment . Fits most 1975 and later non-electronic Rochester Quadrajet carburetors, except some truck and marine carburetors that use the early style rods. Dimension stamped in rod indicates maximum diameter of taper.
Quantity: 2 Primary Metering Rods for Rochester Quadrajet and Dualjet carburetors.
Rod Specifications:
Single taper design “S”
Cruise diameter: .062"
Power tip diameter:.036"
Rod overall length: 2.395" - 2.400"
Does NOT fit Quadrajets or Dualjets with Electronic Mixture Control Solenoid (MCS)
Primary Rod Tech:
A 62S rod has a large diameter of .062" and a small diameter "power tip" of .036". The .062" section of the rod is positioned in the metering jet during light throttle driving. During heavy acceleration, manifold vacuum decreases allowing the power piston to rise positioning the small diameter (.036") power tip in the metering jet.
Larger diameter rods will lean part throttle/cruise air fuel mixtures. All "M" primary metering rods have the same small diameter power tip (.036"). A great way to fine tune your Q-Jet for better driveablity and fuel mileage.
Note: -
For additional in depth information on Primary Metering Rods (Go to the Primary Metering Rod Tech Info page )…see more
- Part Number
- 2562S-NOS
1" Inlet Fitting Gaskets for 1" SELF TAPPING fittings, 5 pack
Hard to find! Replacement inlet fitting gaskets for carburetors with 1" Self Tapping inlet fittings.
We received many inquires from frustrated owners with Quadrajet carburetors that had a 1" self tapping inlet fitting installed but the gasket was either missing, damaged or just not sealing anymore. This gasket was never available separately until we decided to make one. Extra thick to help seal most leaks.
Quantity: 5 gaskets
Gasket OD" 1.3"
Gasket ID" 1.01" (1")
Gasket Thickness: .065"
Fits: Rochester carburetors that originally came with 1"x20 threads and had a self tapping fitting installed.
This gasket is extra thick to help seal 1" self tapping fittings.
Note:
Photo shows self tapping inlet fitting for illustrative purposes only, the fitting is Not include with this gasket pak.
This gasket will not work with original 1"-20 inlet fittings, ONLY 1" self tapping fittings.…see more
- Part Number
- 2233L
1" Inlet Fitting Gaskets, Nylon - 5 pack
1" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located at...see more
Inlet fitting gaskets for Rochester Quadrajet & Dualjet carburetors with 1" diameter inlets.
Quantity: 5 gaskets
Gasket OD" .935"
Gasket ID" .790"
1" inlet fittings are found on all 1972 and later automobile and truck Quadrajet carburetors.
1" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located at the very forward edge of the inlet fitting. After installation of the 1" inlet fitting on the carburetor, the inlet gasket is not visible.
Tech Note:
If you find it difficult to slip gasket onto inlet fitting, try soaking gasket in hot water for 30 seconds to make it more pliable.
This gasket will not work with aftermarket self tapping inlet fittings.…see more
- Part Number
- 2232
1"-20 x 5/8-18" - Banjo Inlet Fitting - Converts front inlet to
Converts inlet position from front to side or side to front. 5/8-18 thread is used...see more
Inlet ‘Banjo’ Fitting for 1"-20 threaded castings. Converts inlet position from front to side or side to front. 5/8-18 thread is used on 3/8" diameter fuel lines. Allows easy positioning of fuel line.
No machine work required, banjo conversion kit contains everything you need including gaskets. Banjo fitting design allows use of most OEM short- style fuel filters. (Note: Mercury marine filter #2254A is longer than our other short filters and is not recommended for use with this banjo fitting. Use #2254 screen filter instead as it is a shorter fiter.)
Quantity: 1
Over-all length: 1.585" (Including threads)
Approximate length protruding from carburetor: 1".
Replacement gaskets available:
#2232 (white/clear gasket, need 1)
#2233 (Red/fibre gasket, need 2)
1" inlet fittings are found on all 1972 and later automobile and truck Quadrajet carburetors.
1" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located at the very forward edge of the inlet fitting. After installation of the 1" inlet fitting on the carburetor, the inlet gasket is not visible.…see more
- Part Number
- 2215
1"-20 x 5/8"-18 - Long Inlet Fitting
Inlet fitting comes complete with sealing gasket. 5/8"-18 threads accept 3/8" fuel line tubing....see more
Replacement Quadrajet inlet fitting fits all 1"-20 thread castings. Inlet fitting comes complete with sealing gasket. 5/8"-18 threads accept 3/8" fuel line tubing.
Fits Rochester Quadrajet carburetors with 1" inlets and 3/8" steel gas line, uses long fuel filter.
Quantity: 1
Replacement gaskets available:
#2232
1" inlet fittings are found on all 1972 and later automobile and truck Quadrajet carburetors.
1" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located at the very forward edge of the inlet fitting. After installation of the 1" inlet fitting on the carburetor, the inlet gasket is not visible.…see more
- Part Number
- 2216
1"-20 x 5/8"-18 - Short Inlet Fitting
Fits Rochester carburetors with 1" inlets and 3/8" steel gas line. Replacement Inlet fitting is 1 3/8" in length. Includes gasket. Depending on carburetor short or long filter may fit.
Male thread: 1"-20
Female thread: 5/8"-18, flared to accept flared steel fuel line.
Quantity: 1 fitting & 1 Gasket
Replacement gaskets available:
#2232
1" inlet fittings are found on all 1972 and later automobile and truck Quadrajet carburetors.
1" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located at the very forward edge of the inlet fitting. After installation of the 1" inlet fitting on the carburetor, the inlet gasket is not visible.…see more
- Part Number
- 2214
1"-20 x 5/8"-18 - Short Inlet Fitting
Fits Rochester Quadrajet carburetors with 1" inlets and 3/8" gas line, uses short...see more
Fits Rochester Quadrajet carburetors with 1" inlets and 3/8" steel gas line, uses short fuel filter. Replacement Inlet fitting is 1 3/8" in length.
Quantity: 1
Replacement gaskets available:
#2232
1" inlet fittings are found on all 1972 and later automobile and truck Quadrajet carburetors.
1" diameter inlet carburetors can be identified by the location of the inlet gasket, it will be located at the very forward edge of the inlet fitting. After installation of the 1" inlet fitting on the carburetor, the inlet gasket is not visible.…see more
- Part Number
- 2214A
1/2" Inlet Fitting Gaskets, 5 pack
Inlet fitting gaskets for carburetors with 1/2" diameter inlets.
Quantity: 5 gaskets
Gasket OD" .690"
Gasket ID" .518"
Gasket Thickness" .046"
Fits:
Carter carburetors
Ford/Motorcraft carburetors
Holley carburetors…see more
- Part Number
- 2233B
1/2" Inlet Fitting Gaskets, 5 pack
Quantity: 5 gaskets
Gasket OD" .727"
Gasket ID" .503"
Gasket Thickness" .031"
Used for:
Inlet fitting gaskets
Needle & seat gaskets
Fits:
Holley carburetors
Asian carburetors…see more
- Part Number
- 2233D
1/2" Rubber Vacuum Caps
Rubber vacuum caps are used to plug unused vacuum fittings. Quantity: 5 caps…see more
- Part Number
- 4294
1/2"-20 x #6 AN Fuel Inlet Adapter Fitting
Adapter fitting allows use of high performance racing fuel hoses and fittings. Adapter fitting has a female 1/2"-20 flared end that screws into the OEM inlet fitting. Number 6 AN male fitting is flared to accept standard #6 AN female hose fittings. Great for high horsepower application where custom steel braided fuel line is used. Fits factory and aftermarket mechanical fuel pumps with 1/2"-20 thread connections.…see more
- Part Number
- 2224A
1/2"-20 x #8 AN Fuel Inlet Adapter Fitting
Adapter fitting allows use of high performance racing fuel hoses and fittings. Adapter fitting has a female 1/2"-20 flared end that screws into the OEM inlet fitting. Number 8 AN male fitting is flared to accept standard #8 AN female hose fittings. Great for high horsepower application where custom steel braided fuel line is used. Fits factory and aftermarket mechanical fuel pumps with 1/2"-20 thread connections.…see more
- Part Number
- 2225A
1/2"-20 x 1/2"-20 Inlet Fitting
Male Threads: 1/2"-20
Female Threads: 1/2"-20 (5/16" flared steel fuel line)
Over all length: .815"
Orifice diameter: .215"
Quantity: 1
Fits:
Ford/Motorcraft 2100 carburetors
Ford/Motorcraft 2150 carburetors
Holley carburetors…see more
- Part Number
- 2218N
1/2"-20 x 1/8 Pipe Thread - Fuel Inlet Reducer Fitting
Female Thread: 1/2"-20 with inverted flare
Male Thread: 1/8" pipe
Overall length: .780"
ID: .200"
Wrench size: 9/16"
Quantity: 1
Fits:
Rochester 2G carburetors
Rochester "B" carburetors
Ford 1100, 1101 carburetors
Ford 4300, 4350 carburetors
Holley carburetors…see more
- Part Number
- 2218J
1/2"-20 x 1/8 Pipe Thread - Inlet Fitting
Male Threads: 1/2"-20
Female Threads: 1/8" Pipe thread
Over all length: .765"
Orifice diameter: .255"
Quantity: 1
Fits:
Ford/Motorcraft 2100 carburetors
Ford/Motorcraft 2150 carburetors
Ford/Motorcraft 2700 VV carburetors
Ford/Motorcraft 7200 VV carburetors…see more
- Part Number
- 2218M
1/2"-20 x 1/8" Pipe Thread - Inlet Fitting
Dimensions:
Male thread: 1/2"-20
Male thread: 1/8" pipe thread
Nut (wrench) size: 1/2"
Quantity: 1 fitting
Fits:
Carter BBS carburetor
Carter RBS carburetor
Carter YF, YFA carburetor
Ford/Motorcraft 4300, 4350 carburetor…see more
- Part Number
- 2218X
1/2"-20 x 5/16" Barbed Nipple
Fits Rochester 4G, 2G and Carter / Edelbrock AFB, AVS...see more
This fitting makes it easy to hook up a rubber gas line to your carburetor. Barbed side of fitting is made to slip into a 5/16" rubber fuel line.
Male Thread: 1/2"-20
Over All Length: 1.280"
Fits Rochester 4G, 2G
Fits Carter / Edelbrock AFB, AVS…see more
- Part Number
- 2243
1/4" Thick Insulating Base Gasket
Fits:
Rochester Quadrajet carburetor
Holley 4010 carburetor
Holley 4360 carburetor
Insulating Spread Bore Base Gasket
4 Hole design, (Thickness: .250" )
Quantity: 1 gasket
Replaces Rochester OEM gasket # 1248516
1/4" thick gasket helps insulate carburetor from intake manifold heat and raises the carburetor to increase plenum volume. Raises the huge secondary throttle plates, relieving upper plenum restriction at full throttle, when used on a dual plane intake manifold.
Nylon buttons at mounting bolt locations prevent over tightening of gasket.
Originally used on the following Rochester carburetor numbers:
7045240, 7045541, 7045548, 17056240, 17056246, 17056540, 17056546, 17058241
Originally used on the following Edelbrock carburetor numbers:
1910
May also fit other applications.…see more
- Part Number
- 1703
1/4" Thick Insulating Base Gasket (Black) OEM # 1248516
Fits:
Rochester Quadrajet carburetor
Holley 4010 carburetor
Holley 4360 carburetor
Insulating Spread Bore Base Gasket
4 Hole design, (Thickness: .250" )
Quantity: 1 gasket
Black color
OEM # 1248516
1/4" thick gasket helps insulate carburetor from intake manifold heat and raises the carburetor to increase plenum volume. Raises the huge secondary throttle plates, relieving upper plenum restriction at full throttle, when used on a dual plane intake manifold.
Four nylon buttons at mounting bolt locations prevent over tightening of gasket.
Q1703A…see more
- Part Number
- 1703A
1/4" Thick Insulating Base Gasket (Open Plenum)
Fits:
Rochester Quadrajet carburetor
Holley 4010 carburetor
Holley 4360 carburetor
Insulating Spread Bore Base Gasket
Open design, (Thickness: .250" )
Quantity: 1 gasket
1/4" thick gasket helps insulate carburetor from intake manifold heat and raises the carburetor to increase plenum volume. Raises the huge secondary throttle plates, relieving upper plenum restriction at full throttle, when used on a dual plane intake manifold.
Nylon buttons at mounting bolt locations prevent over tightening of gasket.…see more
- Part Number
- 1703B
1/8-Pipe Thread x 1/4-Pipe Thread - Fuel Inlet Reducer Fitting
Male Thread: 1/8" NPT (approximately .400" in diameter)
Female Thread: 1/4" pipe
Overall length: .950"
ID: .250"
Wrench size: 5/8"
Quantity: 1
Fits:
Rochester 4G carburetors…see more
- Part Number
- 2218H
1/8-Pipe Thread x 1/4" Barbed Nipple
This fitting makes it easy to hook up a rubber 1/4" gas line to your Rochester carburetor...see more
This fitting makes it easy to hook up a rubber 1/4" gas line to your Rochester carburetor. Threaded male side of fitting is 1/8" pipe thread to seal against the factory inlet fitting.
Barbed side of fitting is made to slip into a 1/4" rubber fuel line.
Male Thread: 1/8" NPT (approximately .400" in diameter)
Fits Rochester 2G carburetors
Quantity: 1…see more
- Part Number
- 2241
1/8-Pipe Thread x 5/16" Barbed Nipple
This fitting makes it easy to hook up a rubber gas line to your carburetor. Barbed side of fitting is made to slip into a 5/16" rubber fuel line.
Fits carburetors with 1/8"-pipe inlet threads.
OAL: 1.245"
Thread length: .270"
Thread: 1/8-NPT male (approximately .400" in diameter)
Barb size: 5/16"
Orifice diameter: .250" …see more
- Part Number
- 2245A
1/8" Rubber Vacuum Caps
Rubber vacuum caps are used to plug unused vacuum fittings. Quantity: 5 Caps…see more
- Part Number
- 4290
2100 & 4100 Brass Float - (Primary)
Fits:
EDSEL 1958-60
FORD/MERCURY 1958-74
FORD TRUCK 1963-75
New Brass float is a direct replacement for the original Ford / Motorcraft / Autolite 4100 Primary carburetor float and 2100 float.
Application:
2100 carburetors
4100 carburetors (primary float)
Original Equiptment Float (OEM) #'s:
FORD OEM Float #: C1AZ-9550-A, C5AF-9550-B
MOTORCRAFT OEM Float #: CM-615
Quantity: 1 Float…see more
- Part Number
- 1450E
2100-2150 Brass Float -
Fits:
AMC 1968-79
EDSEL 1959-60
FORD/MERCURY 1958-86
FORD TRUCK 1963-86
JEEP 1971-92
LINCOLN 1977-82
New Brass float is a direct replacement for the original Ford / Motorcraft / Autolite 2100-2150 carburetor float.
Brass Replacement for:
FORD OEM Float #: D0AZ-9550-A, D4AZ-9550-A
MOTORCRAFT OEM Float #: CM-1062
AMC OEM Float #: 4488178
Interchanges with Nitrophyl float #1450A
Quantity: 1 Float…see more
- Part Number
- 1450B
2100-2150 Nitrophyl Float -
Fits:
AMC 1968-79
EDSEL 1959-60
FORD/MERCURY 1958-86
FORD TRUCK 1963-86
JEEP 1971-92
LINCOLN 1977-82
New Nitrophyl float is a direct replacement for the original Ford / Motorcraft / Autolite 2100-2150 carburetor float.
Float weight: 9.5 Grams
FORD OEM Float #: DOAZ-9550-A, D4AZ-9550-A
MOTORCRAFT OEM Float #: CM-1062, CM-1062A
AMC OEM Float #: 4488178
Interchanges with Brass float #1450B
Quantity: 1 Float
Carburetors serviced with this float:
5752004, 5752005, 5752304, 5752305, 5752306, 5752307, 75TF-AA, 75TF-BA, 75TF-CA, 75TF-DA, 76TF-AB, 76TF-BA, 76TF-CA, 76TF-DA, 77TF-KA, 77TF-LA, B8A-K, B8A-L, B8A-N, B8A-P, B9A-A, B9A-B, B9A-C, C0AE-AB, C0AE-AC, C0AE-AF, C0AE-AG, C0AE-H, C0AE-M, C0AE-R, C0AE-S, C0AZ-A, C0ME-G, C0ME-K, C1AE-AA, C1AE-AB, C1AE-AC, C1AE-AD, C1AE-AE, C1AE-AF, C1AE-Y, C1AE-Z, C2AZ-C, C2AZ-D, C3AF-AK, C3AF-AL, C3AF-AR, C3MY-A, C3MY-B, C3MY-C, C3MY-D, C3OE-N, C3OE-R, C3OE-S, C3OE-T, C3OF-G, C3OF-H, C3OF-L, C3OF-M, C4AF-BE, C4AF-BG, C4AF-BH, C4AF-BV, C4AF-BY, C4AF-EB, C4AF-EC, C4AF-H, C4DF-A, C4DF-B, C4MF-A, C4MY-A, C4MY-B, C4MY-C, C4MY-D, C4MY-E, C4OF-A, C4OF-AC, C4OF-AE, C4OF-AG, C4OF-AK, C4OF-AM, C4OF-AS, C4OF-B, C4OF-D, C4OF-E, C4OF-J, C4TF-G, C4TF-H, C4TF-J, C4ZF-E, C4ZF-F, C5AF-C, C5AF-D, C5MF-A, C5MF-B, C5MF-C, C5MF-D, C5MF-E, C5MF-F, C5MY-A, C5MY-B, C5MY-C, C5MY-D, C5MY-E, C5MY-F, C6AF-A, C6AF-C, C6DF-E, C6DF-F, C6DF-G, C6DF-H, C6MF-A, C6MF-D, C6MF-J, C6MY-A, C6MY-D, C6OF-A, C6OF-K, C6PF-L, C6TF-BH, C7DF-E, C7DF-F, C7OF-AF, C7OF-AK, C8AF-AF, C8AF-AG, C8AF-AH, C8AF-AJ, C8AF-AZ, C8AF-BB, C8AF-BC, C8AF-D, C8AF-R, C8AF-S, C8AF-T, C8AF-U, C8DF-E, C8DF-F, C8OF-AE, C8OF-H, C8OF-J, C8OF-L, C8OF-M, C8OF-N, C8OF-R, C8OF-S, C8OF-T, C8PF-T, C8PF-U, C8TZ-AA, C8TZ-AB, C8TZ-AD, C8TZ-AE, C8TZ-AF, C8TZ-N, C8TZ-Y, C8TZ-Z, C8UF-H, C8UF-J, C8UF-L, C8ZF-E, C8ZF-F, C8ZF-H, C9AF-J, C9AF-Z, C9TF-J, C9TF-K, C9TF-L, C9ZF-G, D0AF-AA, D0AF-AR, D0AF-AS, D0AF-AT, D0AF-AU, D0AF-AV, D0AF-C, D0AF-D, D0AF-E, D0AF-F, D0AF-G, D0AF-H, D0AF-J, D0AF-S, D0AF-T, D0AF-U, D0AF-V, D0AF-Y, D0AF-Z, D0BF-C, D0BF-D, D0BF-F, D0OF-J, D0OF-K, D0OF-L, D0OF-M, D0OF-T, D0OF-U, D0OF-V, D0PF-AH, D0PF-AJ, D0PF-AM, D0TF-A, D0TF-AA, D0TF-AB, D0TF-AC, D0TF-AD, D0TF-AE, D0TF-AF, D0TF-AG, D0TF-B, D0TF-C, D0TF-M, D0TF-N, D0TF-R, D0TF-S, D0TF-Y, D0TF-Z, D0UF-B, D0UF-C, D0UF-E, D0UF-F, D0UF-G, D0ZF-A, D0ZF-B, D1AF-BA, D1AF-DA, D1AF-FA, D1AF-JA, D1AF-KA, D1AF-SA, D1AF-TA, D1AF-UA, D1AF-XA, D1AF-YA, D1AF-ZA, D1BF-AA, D1MF-FA, D1MF-GA, D1MF-JA, D1MF-KA, D1MF-LA, D1MF-MA, D1MY-F, D1MY-FA, D1MY-G, D1MY-J, D1OF-ABA, D1OF-ADA, D1OF-AGA, D1OF-AHA, D1OF-AJA, D1OF-MA, D1OF-NA, D1OF-PA, D1OF-RA, D1OF-UA, D1OF-YA, D1OF-ZA, D1PF-AA, D1PF-BA, D1PF-CA, D1TF-AA, D1TF-AHA, D1TF-AJA, D1TF-AKA, D1TF-ALA, D1TF-AMA, D1TF-ANA, D1TF-APA, D1TF-ARA, D1TF-CA, D1TF-EA, D1TF-HA, D1TF-LA, D1TF-NA, D1TF-TA, D1UF-AA, D1UF-CA, D1UF-DA, D1UF-FA, D1UF-SA, D1YF-CA, D1YF-DA, D1YF-FA, D1ZF-AA, D1ZF-ACA, D1ZF-ADA, D1ZF-AEA, D1ZF-SA, D1ZF-UA, D2AF-EA, D2AF-FB, D2AF-FC, D2AF-FD, D2AF-GA, D2AF-GB, D2AF-GC, D2AF-GD, D2AF-HA, D2AF-HB, D2AF-HC, D2AF-UC, D2BF-AA, D2BF-EA, D2BF-FA, D2FG-AA, D2FG-AB, D2FG-AC, D2FG-BA, D2FG-BB, D2FG-BC, D2GF-AA, D2GF-AB, D2GF-AC, D2GF-BA, D2GF-BB, D2GF-BC, D2MF-CA, D2MF-CB, D2MF-DA, D2MF-DB, D2MF-EA, D2MF-EB, D2MF-FA, D2MF-FB, D2MF-FC, D2MF-FE, D2MF-FF, D2OF-FA, D2OF-JA, D2OF-KA, D2OF-KB, D2OF-KD, D2OF-NA, D2OF-PA, D2OF-RA, D2OF-UA, D2OF-UB, D2OF-UC, D2OF-VA, D2PF-GA, D2PF-GB, D2PF-HA, D2PF-HB, D2PF-JA, D2PF-KA, D2PF-LA, D2PF-MA, D2PF-NA, D2PF-PA, D2PF-RA, D2TF-AA, D2TF-AAA, D2TF-AB, D2TF-BA, D2TF-CA, D2TF-DA, D2TF-DB, D2TF-EA, D2TF-EB, D2TF-FA, D2TF-FB, D2TF-FC, D2TF-FD, D2TF-GA, D2TF-HA, D2TF-HB, D2TF-JA, D2TF-JB, D2TF-KA, D2TF-TA, D2TF-UA, D2TF-YA, D2UF-AA, D2UF-BA, D2UF-CA, D2UF-DA, D2UF-EA, D2UF-HA, D2UF-JA, D2UF-KA, D2UF-LA, D2UF-MA, D2UF-PA, D2UF-YA, D2WF-CA, D2WF-CB, D2ZF-EA, D2ZF-FA, D2ZF-FB, D2ZF-HA, D2ZF-JA, D2ZF-KA, D2ZF-LA, D2ZF-LB, D2ZF-LC, D2ZF-MA, D2ZF-MB, D3AF-ABA, D3AF-CC, D3AF-CD, D3AF-CE, D3AF-DB, D3AF-DC, D3AF-JA, D3AF-KA, D3AF-MA, D3AF-NA, D3AF-PA, D3AF-RA, D3AF-RB, D3AF-UA, D3AF-XA, D3BF-AC, D3BF-AD, D3BF-AE, D3BF-BC, D3BF-BD, D3BF-BE, D3BF-EA, D3BF-FA, D3BF-GA, D3BF-HA, D3BF-HB, D3DE-AA, D3DF-EA, D3GF-AD, D3GF-AE, D3GF-AF, D3GF-BA, D3GF-BB, D3GF-BC, D3MF-AD, D3MF-AE, D3MF-BA, D3MF-CA, D3MF-DA, D3MF-EA, D3MF-FA, D3MF-GA, D3OF-AD, D3OF-AE, D3OF-EA, D3OF-FA, D3OF-JA, D3PF-DA, D3PF-EA, D3PF-EB, D3PF-FA, D3PF-FB, D3PF-GA, D3PF-HA, D3PF-HB, D3PF-JA, D3PF-KA, D3PF-KD, D3PF-LA, D3PF-MA, D3PF-VA, D3TE-AA, D3TE-AC, D3TF-AB, D3TF-BC, D3TF-BD, D3TF-BE, D3TF-CC, D3TF-CD, D3TF-CE, D3TF-DC, D3TF-DD, D3TF-DE, D3TF-DF, D3TF-GC, D3TF-HC, D3TF-MB, D3TF-MC, D3TF-MD, D3TF-ME, D3TF-NA, D3TF-SA, D3TF-UA, D3TF-VA, D3TF-XA, D3TF-YA, D3UF-AC, D3UF-AD, D3UF-CC, D3UF-CD, D3UF-DC, D3UF-EC, D3UF-FC, D3UF-GC, D3UF-RA, D3UF-SA, D3UF-TA, D3UF-YA, D3WF-AC, D3WF-CA, D3ZF-EA, D3ZF-EB, D3ZF-FA, D3ZF-GA, D3ZF-NA, D3ZF-NB, D4AE-CA, D4AE-DA, D4AE-EA, D4AE-FA, D4AE-GA, D4AE-HB, D4AE-KA, D4AF-DA, D4AF-EA, D4BE-AA, D4BE-BA, D4BE-CA, D4BE-EA, D4BE-FA, D4DE-LA, D4DE-NB, D4DE-PA, D4DE-RA, D4DE-RB, D4DE-UA, D4DE-VA, D4DF-AA, D4DF-BA, D4DF-NB, D4ME-BA, D4ME-CA, D4MF-BA, D4MF-CA, D4MF-DA, D4MF-EA, D4OE-CA, D4OE-EA, D4OE-FA, D4OE-GA, D4OE-JA, D4OF-AA, D4OF-BA, D4OF-CA, D4OF-DA, D4PE-AYA, D4PE-AZA, D4PE-BAA, D4PE-BBA, D4PE-BCA, D4PE-BDA, D4PE-BEA, D4PE-BFA, D4PE-BFB, D4PE-BGA, D4PE-BHA, D4PE-BKA, D4PE-BPA, D4PE-BRA, D4PE-BSA, D4PE-BTA, D4PE-BUA, D4PE-BVA, D4PE-BYA, D4PE-BZA, D4PE-CAA, D4PE-CBA, D4PE-CCA, D4PE-CDA, D4PE-CEA, D4PE-CFA, D4PE-CGA, D4PE-EA, D4PE-EB, D4PE-EC, D4PE-FA, D4PE-FB, D4PE-GA, D4PE-GB, D4PE-HA, D4PE-HB, D4PE-JA, D4PE-KA, D4PE-NA, D4PE-PA, D4PE-RA, D4PE-SA, D4PE-TA, D4PE-UA, D4PE-VA, D4PE-VB, D4PE-YA, D4PE-YC, D4PE-ZA, D4TE-ADA, D4TE-AFA, D4TE-AYA, D4TE-AZA, D4TE-BAA, D4TE-BCA, D4TE-BKA, D4TE-CAA, D4TE-DA, D4TE-DB, D4TE-EA, D4TE-EAA, D4TE-GA, D4TE-HA, D4TE-JA, D4TE-LA, D4TE-RA, D4TE-SA, D4TE-TA, D4TE-VA, D4TF-AA, D4TF-BA, D4TF-CA, D4TF-DA, D4TF-HA, D4TF-KA, D4UE-BA, D4UE-CA, D4UE-DA, D4UE-EA, D4UE-FA, D4UE-GA, D4UE-HA, D4UE-JA, D4UE-UA, D4UF-AA, D4UF-BA, D4ZF-NB, D5AE-EA, D5DE-AA, D5DE-AEA, D5DE-AFA, D5DE-BA, D5DE-JA, D5DE-UA, D5DE-VA, D5ME-FA, D5OE-AA, D5OE-BA, D5OE-CA, D5OE-EA, D5OE-GA, D5OE-HA, D5OE-MA, D5PE-BAA, D5PE-BBA, D5PE-BCA, D5PE-BDA, D5PE-BEA, D5PE-BFA, D5PE-BGA, D5PE-BHA, D5PE-BJA, D5PE-BKA, D5PE-BLA, D5PE-BMA, D5PE-BNA, D5PE-BPA, D5PE-BRA, D5PE-HA, D5PE-JA, D5PE-KA, D5PE-LA, D5PE-NA, D5PE-PA, D5PE-RA, D5PE-SA, D5PE-TA, D5PE-UA, D5PE-VA, D5PE-YA, D5PE-ZA, D5TE-AAA, D5TE-AAF, D5TE-ABA, D5TE-ACB, D5TE-ASA, D5TE-ATA, D5TE-AUA, D5TE-AUB, D5TE-AVA, D5TE-AZA, D5TE-BAA, D5TE-BCA, D5TE-BCB, D5TE-BDA, D5TE-BDB, D5TE-BEA, D5TE-BEB, D5TE-BFA, D5TE-BFB, D5TE-BGA, D5TE-BHA, D5TE-BJA, D5TE-BKA, D5TE-BLA, D5TE-BMA, D5TE-BYA, D5TE-BZA, D5TE-LA, D5TE-PA, D5TE-VA, D5TE-YA, D5TE-YF, D5TE-ZA, D5TE-ZB, D5UE-AA, D5UE-BA, D5UE-CA, D5UE-DA, D5UE-DC, D5UE-JA, D5UE-JC, D5UE-JD, D5UE-KA, D5UE-KD, D5UE-LA, D5UE-MA, D5UE-ZA, D5WE-CA, D5WE-EA, D5WE-FA, D5WE-GA, D5ZE-AD, D5ZE-AE, D5ZE-BD, D5ZE-BE, D5ZE-CC, D5ZE-CE, D5ZE-DC, D5ZE-DE, D5ZE-DF, D5ZE-JA, D5ZE-VA, D5ZE-YA, D5ZE-YB, D64E-AA, D64E-BA, D64E-BB, D64E-DA, D6AE-HA, D6AE-JA, D6AE-JB, D6AE-KA, D6FE-FA, D6FE-GA, D6FE-HA, D6FE-JA, D6FE-KA, D6FE-LA, D6ME-AA, D6ME-BA, D6ME-CA, D6ME-DA, D6OE-AA, D6OE-AB, D6OE-BA, D6OE-BB, D6OE-CA, D6PE-AAA, D6PE-ABA, D6PE-ACA, D6PE-AJA, D6PE-AKA, D6PE-ALA, D6PE-AMA, D6PE-ANA, D6PE-APA, D6PE-ARA, D6PE-ASA, D6PE-ATA, D6PE-CA, D6PE-DA, D6PE-EA, D6PE-GA, D6PE-JA, D6PE-KA, D6PE-LA, D6TE-FA, D6TE-GA, D6TE-GB, D6TE-JA, D6TE-MA, D6TE-RA, D6TE-SA, D6TE-TA, D6TE-VA, D6TE-YA, D6TE-YB, D6UE-HA, D6UE-JA, D6UE-NA, D6WE-AA, D6WE-BA, D6WE-CA, D6WE-CB, D6WE-EA, D6WE-FA, D6ZE-AA, D6ZE-AAA, D6ZE-BA, D6ZE-CA, D6ZE-DA, D6ZE-JA, D6ZE-VA, D74E-BA, D74E-DA, D7AE-ACA, D7AE-ACB, D7AE-ADA, D7AE-ADB, D7AE-AHA, D7AE-AHB, D7AE-AKA, D7AE-AKB, D7AE-ASA, D7AE-ATA, D7AE-AVA, D7AE-AYA, D7AE-BA, D7AE-CA, D7AE-DA, D7AE-EA, D7AE-FA, D7AE-GA, D7AE-TA, D7AE-TB, D7AE-YA, D7BE-ABA, D7BE-JA, D7BE-LA, D7BE-MA, D7BE-PA, D7BE-YA, D7DE-KA, D7DE-KB, D7DE-LA, D7DE-RA, D7DE-RB, D7OE-CA, D7OE-CB, D7OE-HA, D7OE-HB, D7OE-HC, D7OE-HD, D7OE-LA, D7OE-MA, D7OE-MB, D7OE-NA, D7OE-NB, D7OE-ND, D7OE-RA, D7OE-RB, D7OE-TA, D7OE-TB, D7PE-AAA, D7PE-ABA, D7PE-ACA, D7PE-ADA, D7PE-AEA, D7PE-AFA, D7PE-AGA, D7PE-AHA, D7PE-AJA, D7PE-AKA, D7PE-ALA, D7PE-AMA, D7PE-ANA, D7PE-APA, D7PE-BGA, D7PE-BHA, D7PE-BJA, D7PE-BKA, D7PE-BMA, D7PE-BNA, D7PE-BPA, D7PE-BRA, D7PE-BSA, D7PE-BTA, D7PE-BUA, D7PE-BVA, D7PE-BYA, D7PE-BZA, D7PE-CAA, D7PE-CBA, D7PE-CCA, D7PE-CGA, D7PE-UA, D7PE-VA, D7PE-YA, D7PE-ZA, D7SE-AA, D7SE-DA, D7TE-ABA, D7TE-ACA, D7TE-ADA, D7TE-AEA, D7TE-AFA, D7TE-AGA, D7TE-AHA, D7TE-AKA, D7TE-ALA, D7TE-AMA, D7TE-ANA, D7TE-APA, D7TE-ARA, D7TE-AUA, D7TE-AYA, D7TE-AZA, D7TE-BAA, D7TE-BEA, D7TE-BPA, D7TE-BVB, D7TE-BYA, D7TE-BZA, D7TE-BZB, D7TE-CJA, D7TE-CKA, D7TE-CLA, D7TE-CTA, D7TE-CUA, D7TE-CVA, D7TE-CZA, D7TE-DAA, D7TE-DBA, D7TE-ZA, D7UE-AAA, D7UE-ABA, D7UE-ACA, D7UE-ADA, D7UE-AEA, D7UE-ANA, D7UE-APA, D7UE-ARB, D7UE-TA, D7UE-UA, D7UE-UB, D7UE-YA, D7UE-ZA, D7UE-ZC, D7WE-EA, D7WE-EB, D7WE-FA, D7WE-GA, D7WE-GB, D7WE-GE, D7YE-AA, D7YE-BA, D7YE-BB, D7YE-EA, D7YE-FA, D84E-EA, D84E-GA, D8AE-JA, D8AE-NA, D8AE-TA, D8AE-UA, D8BE-ACA, D8BE-KA, D8BE-MA, D8BE-MB, D8BE-NA, D8DE-HA, D8KE-DA, D8KE-EA, D8ME-AA, D8ME-BA, D8OE-BA, D8OE-CA, D8OE-EA, D8OE-HA, D8OE-TA, D8OE-UA, D8OE-VA, D8PE-ANA, D8PE-APA, D8PE-ATA, D8PE-AVA, D8PE-AYA, D8PE-BBA, D8PE-BCA, D8PE-BMA, D8PE-BNA, D8PE-BPA, D8PE-BRA, D8PE-BSA, D8PE-BTA, D8PE-BUA, D8PE-BVA, D8PE-BYA, D8PE-BZA, D8PE-CAA, D8PE-CBA, D8PE-CCA, D8PE-CFA, D8PE-CHA, D8PE-CJA, D8PE-CKA, D8PE-CLA, D8PE-CMA, D8PE-CNA, D8PE-CPA, D8PE-CRA, D8PE-CSA, D8PE-CTA, D8PE-CUA, D8PE-CVA, D8PE-DDA, D8SE-CA, D8SE-DA, D8SE-EA, D8SE-FA, D8SE-GA, D8TE-AA, D8TE-ARA, D8TE-ATA, D8TE-BA, D8TE-BEA, D8TE-BJA, D8TE-BLA, D8TE-BNA, D8TE-CCA, D8TE-CGA, D8TE-CHA, D8TE-CJA, D8TE-CLA, D8TE-CPA, D8TE-CRA, D8TE-CTA, D8TE-DA, D8TE-DBA, D8TE-GA, D8UE-CSA, D8UE-DA, D8UE-GA, D8UE-HA, D8UE-KA, D8UE-MA, D8UE-MB, D8UE-SA, D8UE-VA, D8WE-CA, D8WE-DA, D8WE-EA, D8WE-HA, D8WE-JA, D8YE-AA, D8YE-AB, D8ZE-TA, D8ZE-UA, D94E-KB, D94E-LB, D9BE-VB, D9BE-YB, D9DE-JB, D9DE-KB, D9DE-NA, D9DE-NB, D9DE-RA, D9DE-RB, D9DE-RD, D9DE-SA, D9DE-SC, D9ME-BA, D9ME-CA, D9ME-FA, D9PE-AA, D9PE-AAA, D9PE-ACA, D9PE-AEA, D9PE-AFA, D9PE-BAA, D9PE-DA, D9PE-EA, D9PE-FA, D9PE-HA, D9PE-TA, D9PE-UA, D9PE-VA, D9SE-GA, D9TE-ALB, D9TE-AMB, D9TE-BAB, D9TE-BBB, D9TE-BEB, D9TE-BFB, D9TE-BGB, D9TE-BHB, D9TE-BJB, D9TE-BNB, D9TE-BPB, D9TE-BRB, D9TE-BSB, D9TE-BTB, D9TE-BUB, D9TE-CPA, D9TE-CRA, D9TE-CSA, D9TE-CTA, D9TE-DCB, D9TE-DFB, D9TE-DGB, D9TE-DHB, D9TE-DJA, D9TE-DKA, D9TE-DNA, D9TE-DPA, D9TE-DRB, D9TE-DTA, D9TE-DUA, D9TE-DVA, D9TE-EDA, D9UE-DB, D9UE-EB, D9UE-GA, D9UE-HA, D9UE-JA, D9UE-KA, D9UE-LA, D9UE-LB, D9UE-MB, D9UE-NB, D9UE-PA, D9VE-SA, DBA1-AA, DBA1-BA, DBA1-BB, DBA9-AA, DBA9-AB, DBA9-AC, DBA9-BB, DBA9-BC, DBAO-AA, DBAO-AB, DBAO-AC, DBAO-AD, DBAO-AE, DBAO-AF, DBAO-BA, DBAO-BB, DBAO-BC, DBAO-BD, DBAO-BE, DBAO-BF, DEA9-BB, DEA9-BC, DFA0-AA, DFA0-AB, DFA0-AC, DFA0-AD, DFA0-AE, DFA0-BA, DFA0-BB, DFA0-BC, DFA0-BD, DFA0-BE, DFA1-AA, DFA1-BA, DFA1-BB, DFAO-AA, DFAO-AB, DFAO-AC, DFAO-AD, DFAO-AE, DFAO-BA, DFAO-BB, DFAO-BC, DFAO-BD, DFAO-BE, DHMO-BA, DHMO-BC, E0PE-AAA, E0PE-ABA, E0PE-ACA, E0PE-ADA, E0PE-AJA, E0PE-AKA, E0PE-ALA, E0PE-AMA, E0PE-FA, E0PE-RA, E0PE-TA, E0PE-VA, E0PE-ZA, E0TE-BEA, E0TE-BFA, E0TE-BGA, E0TE-BHA, E0TE-BLA, E0TE-BRA, E0TE-BSA, E0TE-BYA, E0TE-BZA, E0TE-CBA, E0TE-CCA, E0TE-CFA, E0TE-CLA, E0TE-CVA, E0TE-CYA, E0TE-CZA, E0TE-DBA, E0TE-DCA, E0TE-DDA, E0TE-DEA, E0TE-DFA, E0TE-DGA, E0TE-EAA, E0TE-EBA, E0TE-ECA, E0TE-EDA, E0TE-EEA, E0TE-EFA, E0TE-EZA, E0UE-AAA, E0UE-ABA, E0UE-NA, E0UE-PA, E0UE-RA, E0UE-SA, E0UE-TA, E0UE-VA, E1PE-AAA, E1PE-ABA, E1PE-ACA, E1PE-ADA, E1PE-AEA, E1PE-BA, E1PE-DA, E1PE-EA, E1PE-FA, E1PE-GA, E1PE-RA, E1PE-SA, E1PE-TA, E1PE-UA, E1PE-VA, E1PE-YA, E1TE-BFA, E1TE-BGA, E1TE-BHA, E1TE-BJA, E1TE-BSA, E1TE-BTA, E1TE-BVA, E1TE-BYA, E1TE-BZA, E1TE-CAA, E1TE-CBA, E1TE-CCA, E1TE-CDA, E1TE-CEA, E1TE-CFA, E1TE-CHA, E1TE-CJA, E1TE-CKA, E1TE-CLA, E1TE-CMA, E1TE-CNA, E1TE-CPA, E1TE-CRA, E1TE-CSA, E1UE-CA, E1UE-FA, E1UE-GA, E1UE-HA, E1UE-JA, E1UE-KA, E24E-AA, E24E-BA, E24E-CA, E24E-DA, E24E-EA, E24E-FA, E25E-AAA, E2BE-AAA, E2BE-ABA, E2BE-ACA, E2BE-ADA, E2BE-AGA, E2BE-AHA, E2BE-AJA, E2BE-AKA, E2BE-ALA, E2BE-AMA, E2BE-UA, E2BE-VA, E2PE-AA, E2PE-ANA, E2PE-APA, E2PE-BDA, E2PE-BJA, E2PE-CKA, E2TE-AYA, E2TE-BAA, E2TE-BBA, E2TE-BEA, E2TE-BFA, E2TE-BGA, E2TE-BHA, E2TE-BJA, E2TE-BKA, E2TE-BLA, E2TE-BMA, E2TE-BNA, E2TE-BPA, E2TE-BRA, E2TE-BYA, E2TE-CFA, E2TE-CGA, E2TE-CHA, E2TE-CJA, E2TE-CKA, E2TE-CYA, E2TE-DAA, E2TE-DBA, E2TE-DCA, E2TE-DDA, E2TE-DEA, E2TE-DMA, E2TE-DNA, E2TE-DRA, E2TE-DTA, E2UE-AAA, E2UE-ABA, E2UE-AHA, E2UE-AKA, E2UE-ANA, E2UE-FA, E2UE-HA, E2UE-JA, E2UE-KA, E2UE-RA, E2UE-SA, E2UE-TA, E2UE-UA, E2UE-VA, E2VE-CA, E2YE-CA, E37E-AAA, E37E-ABA, E37E-ACA, E37E-ADA, E37E-AEA, E3AE-ABA, E3AE-ACA, E3AE-ADA, E3AE-AEA, E3AE-AFA, E3AE-AGA, E3AE-AKA, E3AE-ALA, E3AE-RA, E3AE-SA, E3AE-TA, E3AE-UA, E3CE-AA, E3CE-BA, E3CE-EA, E3CE-GA, E3CE-HA, E3PE-CA, E3PE-DA, E3PE-GA, E3PE-LA, E3PE-LE, E3SE-ANA, E3SE-APA, E3SE-ARA, E3SE-ATA, E3SE-AUA, E3SE-BDA, E3SE-BEA, E3SE-BFA, E3SE-BGA, E3SE-EA, E3SE-FA, E3SE-GA, E3SE-HA, E3SE-JA, E3SE-KA, E3SE-LA, E3SE-MA, E3SE-NA, E3TE-AUA, E3TE-AVA, E3TE-AYA, E3TE-BAA, E3TE-BBA, E3TE-BCA, E3TE-BEA, E3TE-BFA, E3TE-BGA, E3TE-BHA, E3TE-BJA, E3TE-BLA, E3TE-BMA, E3TE-BSA, E3TE-BTA, E3UE-BA, E3UE-CA, E3UE-DA, E3UE-EA, E47E-TA, E47E-UA, E47E-VA, E47E-YA, E4CE-AA, E4CE-BA, E4SE-CA, E4SE-DA, E4TE-ACA, E4TE-ADA, E4TE-AEA, E4TE-AFA, E4TE-AHA, E4TE-AJA, E4TE-AKA, E4TE-ALA, E4TE-AMA, E4TE-APA, E4TE-ATA, E57E-BA, E57E-CA, E59E-AA, E59E-DA, E59E-EA, E59E-FA, E5AE-CA, E5SE-AA, E5SE-BA, E5TE-ACA, E5TE-YA, E69E-AA, E69E-BA, E69E-CA, E69E-DA, EDB-AF, EDB-AG, EDB-U, EDB-V, EDC-A, EDC-B, KBA1-AA, KBA1-BA, KBA1-BB, KFA1-AA, KFA1-BA, KFA1-BB, PB8M-A, PB8M-G, PB9E-B, PB9E-C, PB9E-D, PB9E-G, PB9M-B, PB9M-H, PB9M-H,…see more
- Part Number
- 1450A
2150 Nitrophyl Float -
Fits:
FORD/MERCURY 1975-83
FORD TRUCK 1979-85
LINCOLN 1978-83
New Nitrophyl float is a direct replacement for the original Ford / Motorcraft / Autolite 2150 carburetor float.
Float weight: 8.5 Grams
FORD OEM Float #: D9AZ-9550-B
MOTORCRAFT OEM Float #: CM-3120
Quantity: 1 Float…see more
- Part Number
- 1450C
2700/7200 VV Nitrophyl Float -
Fits:
FORD 1977-91
FORD TRUCK 1981-83
LINCOLN 1977-82
MERCURY 1977-91
New Nitrophyl float is a direct replacement for the original Ford / Motorcraft / Autolite VV carburetor float.
Application:
2700 VV carburetors
7200 VV carburetors
Original Equiptment Float (OEM) #'s:
FORD OEM Float #: FORD D7ZZ-9550-A, D9ZZ-9550-A, D, E0VZ-9550-A, B
MOTORCRAFT OEM Float #: CM-3098 (REPLACES CM-2455)
CARTER OEM Float #: 21-318
Quantity: 1 Float
This float fits the following carburetors:
77TF-MA,77TF-NA,D7ZE-AC,D7ZE-BA,D7ZE-BD,D7ZE-BE,D7ZE-GD,D7ZE-GE,D84E-BB,D84E-DB,D84E-FB,D84E-KA,D84E-VA,D8BE-EB,D8PE-CYA,D8PE-CZA,D8PE-DAA,D8PE-DBA,D8PE-DCA,D8ZE-HB,D8ZE-VA,D8ZE-VB,D8ZE-YB,D94E-AB,D94E-EB,D94E-FA,D94E-GA,D94E-JA,D9AE-ACA,D9AE-AZA,D9AE-BAA,D9AE-CA,D9AE-CB,D9AE-JB,D9AE-YB,D9AE-ZB,D9BE-AFA,D9DE-HB,D9ME-AA,D9PE-BBA,D9PE-BCA,D9PE-BDA,D9PE-BEA,D9PE-BFA,D9PE-BGA,D9PE-BHA,D9ZE-AZB,D9ZE-BEA,D9ZE-LC,E0AE-AAA,E0AE-AAB,E0AE-ACA,E0AE-ACB,E0AE-ADA,E0AE-AHA,E0AE-ALA,E0AE-AMA,E0AE-ANA,E0AE-APA,E0AE-ATA,E0AE-BA,E0AE-BB,E0AE-BC,E0AE-LA,E0AE-LB,E0AE-LC,E0AE-PA,E0AE-PB,E0AE-ZA,E0AE-ZB,E0BE-MA,E0PE-BA,E1AE-AAA,E1AE-ACA,E1AE-AGA,E1AE-KA,E1AE-LA,E1AE-MA,E1AE-SA,E1AE-VA,E1DE-AA,E1PE-AA,E1PE-AKA,E1PE-ANA,E1PE-AUA,E1SE-EA,E1TE-ABA,E1TE-AHA,E1TE-YA,E1TE-ZA,E1VE-AA,E25E-ABA,E25E-AC,E25E-FA,E25E-GA,E25E-SA,E25E-TA,E25E-UA,E2AE-ABA,E2AE-ACA,E2AE-AGA,E2AE-AJA,E2AE-APA,E2AE-AUA,E2AE-LB,E2AE-LC,E2AE-MA,E2AE-MB,E2AE-NA,E2AE-RA,E2AE-TA,E2AE-TB,E2DE-NA,E2DE-SA,E2DE-TA,E2DE-UA,E2PE-AKA,E2PE-ALA,E2PE-BA,E2PE-CA,E2PE-DA,E2PE-EA,E2PE-FA,E2PE-GA,E2PE-HA,E2PE-JA,E2SE-DB,E2SE-EA,E2SE-FA,E2TE-CAA,E2TE-CBA,E2TE-CCA,E2TE-CCB,E2TE-CCC,E2TE-CDA,E2TE-CDB,E2TE-CDD,E2TE-DFB,E2TE-DGB,E2TE-DKA,E2TE-DLA,E3TE-BVA,E3TE-BYA,E7AE-AA,E7AZ-A,E8AE-AA,E8AZ-A,F0AE-AA…see more
- Part Number
- 1450D
2G Accelerator Pump Linkage Rod, fits 1955-69 Chevrolets w/V8
Replaces OEM linkage # 7005816, 7038435...see more
This rod connects the throttle shaft and the accelerator pump. Fits 1955-69 Chevrolets with 2G carburetor and V8 engine.
Overall length: 3.125"
Rod diameter: .150"
Accepts retainer # 4253
Quantity: 1 rod
Replaces OEM linkage # 7005816, 7038435
This item fits the following carburetor numbers:
7023007, 7023008, 7023018, 7024100, 7024101, 7024102, 7024106, 7024108, 7024110, 7024112, 7025088, 7025103, 7027101, 7027103, 7027110, 7027112, 7027114, 7027116, 7028101, 7028103, 7028110, 7028112, 7029101, 7029103, 7029110, 7029112, 7036101, 7036103, 7036110, 7036112, 7037101, 7037103, 7037110, 7037112
May also fit other applications.…see more
- Part Number
- 3130-2G2
2G Choke Rod - (OEM# 7010055)
Fits Rochester 2G carburetors.
Overall length: 2.850"
Rod diameter: .187"
Quantity: 1 rod
Replaces OEM linkage # 7010055
This item fits the following carburetor numbers:
7023041, 7023042, 7023043, 7023145, 7023146, 7029123, 7040123, 7041123, 7042123, 7043123, 7044133, 17054659, 17056433, 17058423
May also fit other applications.…see more
- Part Number
- 3080-2G5
2G Choke Rod - (OEM# 7026559)
Fits Rochester 2G carburetors.
Overall length: 2.6"
Rod diameter: .125"
Quantity: 1 rod
Replaces OEM linkage # 7026559
This item fits the following carburetor numbers:
7024100, 7024101, 7024102, 7024106, 7024108, 7024110, 7024112, 7024183, 7024186, 7025088, 7025103, 7027101, 7027103, 7027110, 7027112, 7027114, 7027116, 7028101, 7028103, 7028110, 7028112, 7028184, 7028185, 7029101, 7029103, 7029105, 7029110, 7029112, 7036101, 7036103, 7036110, 7036112, 7037080, 7037101, 7037103, 7037110, 7037112, 7040101, 7040103, 7040105, 7040108, 7040110, 7040112, 7040125, 7040400, 7040401, 7040403, 7040405, 7040406, 7040407, 7040408, 7040410, 7040412, 7040425, 7041101, 7041105, 7041110, 7041111, 7041125, 7041126, 17054658, 17055000
May also fit other applications.…see more
- Part Number
- 3080-2G7
2G Choke Rod - 1969-74 Chevy, (OEM# 7036186, 7043370)
Fits Rochester 2G carburetors. Overall length: 2.850...see more
Fits Rochester 2G carburetors.
Overall length: 2.850"
Rod diameter: .125"
Quantity: 1 rod
Replaces OEM linkage # 7036186, 7043370
This item fits the following carburetor numbers:
7029102, 7029104, 7029113, 7029114, 7029115, 7029116, 7029117, 7029118, 7029119, 7029120, 7029121, 7029127, 7029129, 7040102, 7040104, 7040113, 7040114, 7040115, 7040116, 7040118, 7040120, 7040126, 7040127, 7040128, 7040129, 7040134, 7040136, 7040402, 7040404, 7040413, 7040414, 7040415, 7040416, 7040418, 7040420, 7040426, 7040427, 7040428, 7040429, 7040434, 7040436, 7041102, 7041113, 7041114, 7041118, 7041127, 7041137, 7042111, 7042112, 7042113, 7042114, 7042118, 7042831, 7042832, 7042833, 7042834, 7042838, 7043108, 7043111, 7043112, 7043113, 7043114, 7043118, 7043119, 7043134, 7044111, 7044112, 7044113, 7044114, 7044115, 7044116, 7044118, 7044123, 7044124
May fit other applications.…see more
- Part Number
- 3080-2G1
- Servicing Bi-Metal Choke Springs
- Ethanol (E-10) fuel in carbureted engines
- Where do I locate my carburetor number?
- How to Test a Vacuum Break / Pulloff
- #4802 Idle Pickup Tubes
- #3622 Power Piston Retaining Bushing
- O-Ring Inlet Repair Fuel Fitting
- #2702 Secondary Air Valve Spring Tension
- #4231B - Air Cleaner Repair Bracket
- Needle & Seats
- #2701 Secondary Air Valve Cam Replacement
- #2460-82 Changing Primary Metering Jets
- #2251/2252/2253 Fuel Filter Replacement
- #1742/1743 Secondary Well Plug Fix
- Float level adjustment for Quadrajet and Dualjet Carburetor
- Servicing the tamper resistant choke cover on Rochester carbs
- #1310-SR Mixture Control Solenoid Adjust
- What is a Carter Quadrajet?
- Quadrajet Model Designations
- Edelbrock Quadrajets
- #1003 Accelerator Pump Styles
- Exploded View 4MV 1975 thru
- Exploded View 4MV 1971 thru 1974
- Exploded View 4MV 1967 thru 1970
- Exploded View 4MV 1966
- Fuel Pressure
- Power Piston & Primary Metering Rods
- Fuel Inlets
- Exploded View 2G / 2GV
All Topics
- Carburetor Tech Info
- Mercury Marine Mercarb Carbureto
- Rochester 2G/Two Jet Tech
- Rochester Quadrajet Tech
Articles RSS Feed
Submit An Article